Ultra MBX R2 Instruction Manual

01Assembly of the right and left hand side are the same.30151Lower Arm Shaft3mmE-Ring4 x 10mmTapping Screw3mmE-RingRR* Insert drive shaft bef

0 10 20 30 40 50mm* Adjust the upper rods length according to the holes chose for attac

1 Degree1.5DegreeFig.1* Set triangle marks in the direction shown in Fig.1.Assembly of the right and left hand side are the same.0 1

ASSEMBLY OF THE WING SUPPORT3 x25mmFlat HeadTapping Screw3 x25mmFlat HeadTapping Screw3 x 20mmFlat HeadTapping screw3 x 20mmFlat HeadTapping screw3027

ASSEMBLY OF THE SERVO SAVER3 x 15mmScrew36742Servo SaverBushing36742Servo SaverBushing36750Servo SaverConnector3mmNylon Lock Nut3mmNylon Lock Nut6 mm

ASSEMBLY OF THE FRONT PLATE ANDSTEERING ROD3 x 15mm Flat Head Screw 3 x 20mm Flat Head Screw 3mm nylonLock Nut

4 x 16mmFlat HeadTapping Screw 34040Chassis, UltraNo Kick-up34040Chassis, UltraNo Kick-up302403411030700 Misc. Screws

34050Center Drive Shaft (Rear)* Insert drive shaft into cap joint.4 x 16mmFlat HeadTapping Screw4 x 16mmFlat HeadTapping ScrewRR3 x 25mmFlat Head Tapp

3 X 8mm Washer 3mm Nylon Locknut 3 x 5mm Screw 3 x 20mm Cap Screw* Place the clutch shoes with the clutch springs over the 3

INSTALLATION OF THE FUEL TANKAND ENGINE ONTO CHASSISNote Book Paper*Use note book paper to set gear backlash between spur gear and clutch bell gear. I

THINGS NEED BESIDES THE KITRADIO CONTROL UNIT 12V Battery for Starter Box(must have)Glow Plug Heat with Battery & Charger# 10227...$$19.95(please

ASSEMBLY OF THE FUEL TUBE* Connect to fuel nipple.* Connect to carburetor. * Connect to fuel tank pressure nipple.ASSEMBLY OF THE

3 x 10mm Screw3 x 10mm Tapping ScrewScrew CementASSEMBLY OF THE SERVO AND REAR STIFFENER34070RearStiffener34031Nylon Post3 x 10mm Tapping ScrewSteeri

30560Antenna Tube andMountTop plate shown is old type!* Battery Case is provided by RadioIt is Recommended to place battery case into aplastic bag bef

* Take the plastic collar from brake system plastic parts.3X3mmSet Screw#158Alum.StopperFuel Tube ( 6mm )* Snap On.3X3mmSet Screw10300Alum.Stop

304106mm Ball End304106mm Ball End0 10 20 30 40 50mm304116mm Ball & Socket304023 X 30

304036mmBall, No Collar3061030600

ASSEMBLY OF THE TIRES, FOAM INSERTS AND WHEELS#86044 - Red#86045 - White#86046 - Lime#86047 - Yellow17mm 5-Star Wheels#86091Mini XX- Pin Tire#1507117m

SoftFirmSoftFirmSoftFirmSoftFirm

STEP 1STEP 2STEP 3STEP 4STEP 5STEP 6STER 7STER 10STEP 8STEP 9

3 x 10mm Flat Head Tapping Screw3 x 15mm Flate Head Tapping Screw3 x 20mm Flat Head Tapping Screw 3 x 25mm Fla

READ THIS BEFORE RUNNINGRunning a nitro kit is fun and easy, but to make this a safe rusting.• Clear oil and dirt from chassis with a degreaser.and g

ENGINE BREAK-IN AND TUNNING(BREAK-IN THE ENGINE BEFORE DRIVING THE CAR!)OPTIONAL OFNA CAR STANDS IN 4 COLORSTUNING AFTER BREAK-IN USING A FORCE .21 EN

32237RebuildKit2. Pull down piston, attach pressure top and shock oil overflow with tissue paper. SHOCK ASSEMBLYFILLING THE SHOCKS WITH OILASSE

301213 x 5mm Screw(Small Head)ASSEMBLY OF NEW “K” STYLE DIFFERENTIAL CASE AND GEARS30751 Diff. Case ( Front/Rear )30761 Diff. Case (Center ) 30751 Di

Screw CementScrew Cement5 x 5mm Set Screw3104030170Brake Cap Joint30170Brake Cap Joint306207x19x5mmBall Bearing306207x19x5mmBall Bearing90026900263021

30201Center Diff. Mount, new30201Center Diff. Mount, new30180Brake Pads30180Brake Pads30180Brake Pads30180Brake Pads30190Brake Disk30190Brake Disk3065

ASSEMBLY OF THE GEAR BOX( Assemble two gear boxes for front and rear. ) 5 x 5mm Set Screw30130Bevel Gear* Place set screw in D cut. 2306306 x 13 x

3 x 20mmFlat Head Tapping Screw30160Front LowerArm Holder4 x 15mmTapping Screw( Small Head ) 0101Assembly of the right and left hand side are the same